This Old House
If you're missing anything, don't proceed until you have a replacement. Drilling Holes in the Cabinet. Tape the provided paper template onto the interior wall. Follow the manufacturer's instructions for all alterations. Your microwave's installation kit should come with self-aligning screws.
Do I still need to shut off the electricity in the kitchen? You can be killed or seriously injured if you don't immediately. How do I adjust overhead cabinets in order to add a hanging microwave over the stove?
Include your email address to get a message when this question is answered. If there is not an outlet in a convenient location, contact an electrician for assistance installing one before you put the microwave in place. Measure the distance between this mark and the floor, and the top of your range, tender fields to make sure that the microwave will be situated within the acceptable height range.
Tools List for Installing a Microwave Hood with Exhaust Fan
- While a helper holds the microwave in position, insert the mounting bolts down through the bottom of the cabinet and into the threaded holes in the top of the unit.
- Can a microwave be mounted without a wall in the back?
- For Back Venting If the ductwork installation has been correct, the microwave's vent fitting should slide smoothly into the collar of the exterior vent cap.
- At the last segment, cut down the section of ductwork to fit, using metal shears, if necessary.
After you make sure you have the supplies you need for installation, double-check that your microwave will fit properly above your range. Drill pilot holes then cut a hole in your roof for the vent roof cap. Slide the exhaust fan supplied with your microwave into place at the ventilation site. If the rest of your electrical appliances are behaving normally, the circuit breaker is probably not the issue. Adjust the height of the bracket based on the cabinet and microwave configuration, following the manufacturer's instructions.
Do not run the microwave empty. Explore other areas for troubleshooting. There are smaller, lighter weight microwaves which can be mounted under a counter. Otherwise, select a spot easily accessible by the power cord and out of the way of normal cabinet function. Otherwise the overhang will block access to the microwave.
Preparing the Microwave Vent. Tighten the bolts securely. Use an appropriate microwave. Installing an Electrical Outlet. For a microwave that requires base-of-cabinet attachments, you may need to saw off the overhang instead.
Turn the circuit breaker off while you investigate other reasons the microwave isn't working. Reframing does not have an impact on the ventilation direction. We have provided many important safety messages in this manual and on your appliance. Most metal ductwork is round, so these openings will be round.
Check every surface of your microwave for vents. Just because the microwave didn't work on your first try does not mean it's defective. Replace the turntable and plug the microwave in. They should slip into slots in the top of the microwave.
Check the installation instructions that come with your particular model to be sure. Before you go through the whole trouble of trying to install the microwave, make sure it has all of the parts it needs. Locate the two or more holes along the upper edge of the microwave.
Microwave Link Installation Alignment and Testing
Anchor this backer strip securely to wall studs. If your kit is missing any parts, return to the store you bought it from to exchange it, or contact the manufacturer to order the component you lack. Thread bolts through the bottom of the cabinet. Contact a contractor to install a new ventilation system. This will usually mean applying some type of silicone caulk or roofing cement, then securing the flanges on the vent cap with nails or screws.
Mostly likely, you will only need to go out and buy a few tools for installing your over-the-range microwave. The last segment of ductwork should be flush with the wall surface back venting or the top of the upper cabinet top venting. Follow these methods for finding and marking these vertical wall supports. If your microwave came with a base of cabinet template, tape this where the microwave top will be located and drill where instructed for the power cord. You can even drill right through the paper.
Because the cabinet does not allow as much air movement around the vents, dust will gradually build up and increase the risk of fire. Avoid doing this, though, because you might end up purchasing the wrong piece. If using your microwave causes a power outage in part of your home, plug it into an outlet on a different circuit or reduce your electrical load.
Apply Paper Template on Wall. Other types may require more advanced ventilation installation. None of these tools are very expensive. If you are lucky enough to have a wall stud positioned at the exact center of the bracket, you can drive the center mounting screw for the bracket directly into this stud. Reframe the opening, top dating sites in the if necessary.
If you don't have an exhaust vent from the top of your range out the roof of your house, the fan functionality can only vent back into the home. Some models also come with a mounting bracket that will have pre-drilled holes so you can easily screw it in place. It's the one piece that carries all the weight.
If your microwave came with a wall template, tape that instead as a drilling guide before you attach the plate. What if it's already unplugged and I'm installing a new microwave? Verify that your microwave is getting power, and test it by heating something to make sure that the appliance is working properly. If your model has a wall plate, fit it into the bracket that will help hold it in place.
Installing an Over-the-Range Microwave Oven With Vent Fan
At least one should be completely over a wall stud to support the microwave's weight. Microwave ovens are heavy, and this step calls for a helper or two as you lift the oven into position and secure it. Mark the site on the wall. If you are using ductwork, secure the first section of rigid metal ductwork to the inner collar on the vent cap, who is camila using sheet metal screws. Use a level to ensure your microwave isn't installed at a slant.
- Connect the metal ductwork to the vent opening on the microwave.
- Tighten until the top of the microwave and the base of the cabinet are flush.
- This likely means that you'll need to add a new electrical circuit and outlet within reach of the oven's power cord.
- This will allow your partner to let go.
It should, but it's not a requirement. See if your microwave has an installation template or wall plate. You'll need to install the over-the-range microwave to studs, not wallboard. Make sure damper plate tabs are inserted into the slots in the top of the microwave oven.
Mark hole locations for the mounting screws. Using measuring tape, find and clearly mark the vertical centerline of the opening. Place your hand near each side of the microwave to feel for blowing air.
Why does my exhaust come out of vents back into my house? Secure the mounting plate. Things You'll Need A drill and set of drill bits. Use the circles you drew as a guide, not the mounting plate. Upload a picture for other readers to see.
Do not vent exhaust air into concealed spaces, such as spaces within walls or ceilings, attics, crawl spaces, or garages. Contact the kit's manufacturer for a replacement. These microwaves usually fit between adjoining wall cabinets and below a specialty upper cabinet that hides the vent connections and electrical outlet. Click here to share your story. Have your helper hold the bulk of the weight while you reach around back and hook the slots to the tabs on the metal mounting plate.