Hook up speakers to factory radio, how to add an amplifier to a factory stereo

Quick Links

Whenever necessary, defer to the instructions included with your speakers, as these will be specifically suited to your unique product. Ensure that the speakers you've chosen fit your car. Because of this, any single list of tools is likely to be insufficient for installing some speakers and redundant for others.

  • If not, you may need to connect the woofer directly to the battery and the car's stereo and ground the woofer manually.
  • Wear hearing protection when adjusting the amp's settings.
  • Geode Painted UpCycled Chairs.
  • Include your email address to get a message when this question is answered.
  • Reconnect your car battery, and test your new audio system.
Adding subwoofer to stock car radio Polk Audio

Can i hook a sub up to that or do i need to get an aftermarket radio? Run this wire back to your amp and hook it into the speaker-level inputs. If they are, then hook up an external speaker to the radio's output for that side to see if it is the radio at fault.

Make sure the fuse you choose is only active when the car is on. Music is like candy, you have to get rid of the rappers to enjoy it. Every amp has pre-drilled mounting screw holes located on each of the four corners of the amp for easier mounting. You do realise that it's the battery that charges the capacitor, right? Take any panels or speaker grilles off.

Your rear speakers are on the rear deck, so its easy to tag on to your speaker wires there. Usually, connecting your new speaker is a fairly simple matter of plugging your speaker's wiring harness into the car's wiring harness. Set all of the input level gain controls to their lowest setting. As with woofers, tweeters, which produce high-pitch frequencies, can be easy or difficult to install based on the factory components of your car.

How do i hook up my amp to my factory radio

Nearly all speakers in the interior of a car will be covered with some sort of protective paneling or grill. This tutorial will focus on how to add an amp by using speaker-level inputs to tap into your car's existing wiring. Now attach a line of speaker wire to each splice and secure with electrical tape. Disconnect the negative battery terminal.

How to Add an Amplifier to a Factory Stereo

Step 2 Wiring Plug

If your speaker won't work, this means that there is a problem with its electrical connection. Note that the speaker is usually, but not always, attached to a wiring harness, so take care not to rip it out when removing it. Tape up your scotch blocks to stop them rattling around and to keep the cables bundled up neatly. Once you're confident that your speaker works properly, secure it in its seat in the door or dash. Make sure the control wire from your deck to the amp is connected.

Cookies make wikiHow better. There is a really long thread on this topic over on crutchfield where a couple of electrical engineers explain in much more detail than I can. It looks like you're new here.

How can i hook up a amp to a factory radio - Free Chat

You can usually find one on the sidewall behind the carpeting. Warnings Never drill inside a car's parts unless you know exactly where the drill bit is going. Free Shipping on All Orders!

Adding RCAs to a Standard Car Head Unit

What Are Some Alarms for an Expensive Audio System

Very cool, but one contemplation here. Did you make this project? Make sure you match the polarity of the car and speaker's connections. For instance, age many people who want to add multiple woofers to their car custom-install a panel in the trunk to house the woofers.

It Still Works
How to Install Car Speakers (with Pictures) - wikiHow

Put a rubber grommet in the hole to keep the wire from chaffing. Do you know if the stock speaker have connection for a Sub? You may find many different styles and colors of trim and covers in a similar price range, so it makes sense to pick the ones that look good, not just sound good. Set equalizers to their center, or neutral, position if you have them. Make sure to connect positive to positive and negative to negative.

And if so, would you have to run wires from the door speakers to the sub location, and then another set of wires back to the doors to the speakers? Generally, the positive wire will be red and the negative will be black. However, if you're asking about the wires from the vehicle, it will depend on the manufacturer. Run the wire under the carpet by removing the rocker panel and kick panel covers. Warning Never let your amp rest freely in your car without being mounted, because it can shift while you're driving and damage the wires or even pose a fire hazard.

How to Install a Car Amp (with Pictures) - wikiHow

What Do You Need to Hook Up an Amplifier to a Car Stereo - Howcast

If your car didn't come with factory subwoofers, however, or you'd like to install additional ones, your task may be much harder. The work you'll have to do to access your car's factory speakers will vary from car to car. Now that your amp is tapped into your car's factory audio system, run speaker wires from the amp's speaker outputs to the speaker s or sub-woofer s you want the amp to power. Can I still add the sub to the stock radio? While your key and radio is on, dating vintage disconnect and connect the remote wire to the amp.

Step 1 Bits and Tools

Don't guess the code as you usually only get a few attempts before it will permanently lock it'self! At the back of your stereo there is most likely one big plug which incorporates all of the inputs and outputs to and from your head unit. Everything works fine but sometimes i get a loud humming sound from the subwoofer. Consult the owner's manual or the manufacturer of your amplifier to determine the size fuse you should use.

Okay, now you'll need to match up your head unit wiring with the wiring required by your converter. Connect the wires just like you would to your speakers. Start with a pilot hole and then work your way up to a size that will fit your wire. The balance on your radio may have gotten moved from center to right or left, or your speaker wire may have come disconnected. Installing an amp can be done without the help of a professional, allowing you to get great sound without an installation fee.

  1. The installation is quick and easy and won't require removing your factory head unit.
  2. If you don't already have one, purchase a car amplifier with speaker-level inputs and also purchase an amp installation kit.
  3. Turn up the deck's volume until you hear distortion, and set it just below that level.
  4. Adding an amp will make your audio system sound louder and clearer by allowing you to send more power to your factory speakers or sub-woofers.

Adding subwoofer to stock car radio

You can put it through an empty rubber grommet in a factory hole. Check your balance first on your radio's settings. This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. Pry the grill off with a suitable tool, like a flat head screwdriver, removing any bolts or screws that are holding it in place if necessary.

  • Dating u beogradu
  • Tucson az dating scene
  • Country guys dating sites
  • Name based matchmaking
  • Frederick md hook up
  • Dating a man from ghana
  • Free country dating websites
  • Best all free online dating